jmdm54
10-02-2007, 02:17 AM
This config worked perfect for me! Good Luck !! (My Model - Innomedia MTA 6328 - 2Re)
http://gizmopasswords.blogspot.com/2007/07/innomedia-for-viatalk.html
Innomedia Configuration for ViaTalk
From: http://www.dslreports.com/forum/r18692448-VERIFIED-guide-use-Innomedia-Gizmo-on-ViaTalk-
This is assuming your box is already unlocked.
1. Disconnect your WAN port from the gizmo
2. Open your browser. Type in your url address line 192.168.251.1/Voice_adminPage.htm - (the IP Address will verify if you changed the default settings in the gizmo. If so, use that IP address, but DO NOT FORGET the /Voice_adminPage.htm at the end)
3. Login using your admin password. If you do not know the password, try one available at »gizmopasswords.blogspot.com
If you do a factory default reset http://gizmopasswords.blogspot.com/2007/07/innomedia-gizmo-bricked-try-this.html with the internet (WAN) unplugged, then un-check provisioning and reboot the device, you can then use user=admin and then pw=slapshot to access the admin panel, at least on the 6328, may work on other Innomedia devices?
4. Turn off provisioning if you have not done this already. To do this, go to NETWORK -> Provisioning setting. Uncheck the "Enable Provisioning" box and hit the "Save and Reboot" button. After rebooting, you may not be able to login to the admin account since the reboot will default to index.htm. Hit CANCEL, and go to »192.168.251.1/Voice_adminPage.htm to login.
5. Go to VOIP -> SIP Proxy and enter these settings:
1. SIP Proxy - Enter exactly what is in your soft phone page from ViaTalk (one of the Server Names) Remove any whitespaces at the end.
2. Check "Use Outbound Proxy" box
3. SIP Local Signaling Port: 5060
4. SIP Domain:
5. Registration Expiration time: 60
6. Preferred Codecs List: PCMU/8000
7. Choose "NONE" for all others.
8. Click "Save" button.
6. Go to VOIP -> User Account.
1. Choose Line 1 from dropdown
2. User ID: Your 11-digit phone number from email (starting with country code 1)
3. Password: From soft phone page on Via Talk site.
4. User Name: Same as User ID above
5. Authentication ID:
6. Use Hot Phone Number: NO
7. Hot Phone Number:
8. Use T38 FAX: Yes
9. Click "Save" button
Reboot your cable/dsl modem, then reboot your gizmo, and power-cycle your phone (if it is a powered phone). ENJOY!!
Check under the "information" to see if line 1 is registered
* Note that when the port of your SR number to ViaTalk is complete, you'll need to use your old SR phone number in place of your temp ViaTalk number in these configs.
http://gizmopasswords.blogspot.com/2007/07/innomedia-for-viatalk.html
Innomedia Configuration for ViaTalk
From: http://www.dslreports.com/forum/r18692448-VERIFIED-guide-use-Innomedia-Gizmo-on-ViaTalk-
This is assuming your box is already unlocked.
1. Disconnect your WAN port from the gizmo
2. Open your browser. Type in your url address line 192.168.251.1/Voice_adminPage.htm - (the IP Address will verify if you changed the default settings in the gizmo. If so, use that IP address, but DO NOT FORGET the /Voice_adminPage.htm at the end)
3. Login using your admin password. If you do not know the password, try one available at »gizmopasswords.blogspot.com
If you do a factory default reset http://gizmopasswords.blogspot.com/2007/07/innomedia-gizmo-bricked-try-this.html with the internet (WAN) unplugged, then un-check provisioning and reboot the device, you can then use user=admin and then pw=slapshot to access the admin panel, at least on the 6328, may work on other Innomedia devices?
4. Turn off provisioning if you have not done this already. To do this, go to NETWORK -> Provisioning setting. Uncheck the "Enable Provisioning" box and hit the "Save and Reboot" button. After rebooting, you may not be able to login to the admin account since the reboot will default to index.htm. Hit CANCEL, and go to »192.168.251.1/Voice_adminPage.htm to login.
5. Go to VOIP -> SIP Proxy and enter these settings:
1. SIP Proxy - Enter exactly what is in your soft phone page from ViaTalk (one of the Server Names) Remove any whitespaces at the end.
2. Check "Use Outbound Proxy" box
3. SIP Local Signaling Port: 5060
4. SIP Domain:
5. Registration Expiration time: 60
6. Preferred Codecs List: PCMU/8000
7. Choose "NONE" for all others.
8. Click "Save" button.
6. Go to VOIP -> User Account.
1. Choose Line 1 from dropdown
2. User ID: Your 11-digit phone number from email (starting with country code 1)
3. Password: From soft phone page on Via Talk site.
4. User Name: Same as User ID above
5. Authentication ID:
6. Use Hot Phone Number: NO
7. Hot Phone Number:
8. Use T38 FAX: Yes
9. Click "Save" button
Reboot your cable/dsl modem, then reboot your gizmo, and power-cycle your phone (if it is a powered phone). ENJOY!!
Check under the "information" to see if line 1 is registered
* Note that when the port of your SR number to ViaTalk is complete, you'll need to use your old SR phone number in place of your temp ViaTalk number in these configs.